Home Brands Bosch Error codes Bosch error codes and indicator lights Each table applies only to the model named above it.
Code Meaning on HBL8451UC E-code The oven has detected a fault. SELECT MODE No cooking mode was selected within 5 seconds of entering a temperature. TEMP NOT ALLOWED The temperature entered is outside the allowed range for the selected mode. SABBATH NOT AVAILABLE A timer was running when Sabbath Mode tried to start. SABBATH ON Sabbath Mode is running. SABBATH ON shows while the Sabbath timer counts down, then the display shows the time and SABBATH. COOLING DOWN The Self Clean timer ended, and the oven must cool before the door can unlock. TIMER END The kitchen timer reached zero. OVEN TIMER FINISHED The oven timer reached zero and the cooking mode ended. Door Lock symbol The oven door is locked. The symbol blinks while the door locks for Self Clean and stays lit while Self Clean runs. Panel Lock symbol The control panel is locked and all buttons are disabled.
Code Meaning on B36CL80SNS E or d The electronics detected a fault. Er The appliance self-test found a fault. Five audible signals sound at the end of the test. Er (Home Connect update) The appliance was unable to install the Home Connect software update. UP An update for the Home Connect software is available. SI Signal strength of the Wi-Fi network: 0 is no reception and 3 is full reception. The value should be at least 2. alarm off flashing The door alarm is on because an appliance door is open, or, if the freezer temperature display also flashes, the temperature alarm is on because the freezer is too warm. change fliter lit The filter change notification comes on every 6 months, sooner with increased water consumption. The control panel prints the label as "change fliter".
Indicator Meaning on SHE53C85N 4 LEDs lit Water is not draining or not coming in, or the supply voltage is too low. Bosch lists six causes. 4 LEDs flashing Bosch describes this as a technical fault and gives no owner-level cause. All LEDs lit or flashing Either a software update is installing or the electronics have detected a fault. Rinse aid indicator lit The rinse aid dispenser is empty.
Code Meaning on SHP78CM5N E:20-60 The dishwasher has detected that the heating element is calcified. E:21-30 The intake opening of the Zeolite container is covered by dishware. E:30-00 The water protection system is activated. E:31-00 The water protection system is activated. E:32-00 Water is not coming in. E:34-00 Water is continuously running into the dishwasher. E:61-02 Not an appliance error: the drain pump cover is loose or a foreign object blocks the pump. E:61-03 Not an appliance error: water is not draining. E:61-60 Technical error. E:90-01 The power voltage is too low. Bosch says the dishwasher itself has no problem. E:92-10 The lower spray arm cannot turn freely. E:92-40 The filters are soiled or blocked. E:01-00 to E:90-10 A technical issue. This covers every code from E:01-00 to E:90-10 that has no entry above. UP A software update is available. All LEDs lit or flashing Either a software update is installing or the electronics have detected a fault. Rinse aid indicator lit The rinse aid dispenser is empty.
Code Meaning on WGG244A9GB E:36 / -10 The water is not draining. Bosch lists blockages in the drain path, a loose pump cap or cover, a drain hose mounted too high and too much detergent. E:30 / -10 Not enough water is coming in, or the water level measurement has failed. With this message the machine starts to drain. E:30 / -20 Bosch lists a defective solenoid valve, too much detergent, or water added to the machine during operation. E:10 / -00, -10 or -20 The pump of the i-DOS intelligent dosing system is blocked. E:60 / -2B The unbalance detection stopped the spin because the laundry is unevenly distributed. Other E codes A malfunction. Bosch gives no owner remedy. Door symbol flashing The door is not closed properly. Detergent drawer symbol lit The detergent drawer is not pushed in fully, or its i-DOS pump unit is missing. i-DOS dispenser symbol flashing That i-DOS dispenser is below its minimum fill level. Drum clean reminder flashing No programme at 60 °C or above has run for a long time, and the drum needs cleaning. Childproof lock symbol flashing The childproof lock is on and a control was used. A steady symbol means the lock is on.