GE GDF535PSRSS dishwasher
- Category
- Dishwashers
- Model number
- GDF535PSRSS
- Region
- United States and Canada
- Verified
- Rating label
- On the left or right front inside edge of the tub, or on the right side edge of the door. Source: support page
- Start light flashing
- Start LED flashing in a sequence
- Clean light
- Sanitized light
- Dishes and flatware are not clean
- Spots and filming on glasses and flatware
- Cloudiness on glassware
- A white film on glassware, dishware and the interior
- Suds in the tub
- Detergent left in the dispenser cups
- Dishes do not dry
- Dishwasher will not run
- Water is standing in the bottom of the tub
- Water will not pump out of the tub
- Control panel lights go off while setting controls
- The dishwasher beeps once every minute
- How to clean the filters
- How to clean the air gap
- How to fill the rinse agent dispenser
- How to remove white film with citric acid
- How to cancel a wash cycle
Nothing on this page matches. Search all models
Indicator lights
| Indicator | Meaning | Checks |
|---|---|---|
| Start light flashing | The door was opened or the cycle was interrupted. | Checks |
| Start LED flashing in a sequence | A critical fault is present. | Checks |
| Clean light | A wash cycle is complete. The light stays on as a reminder that the dishes are clean. | Checks |
| Sanitized light | The sanitizing conditions were not met. | Checks |
GE Appliances codes on other models
Start light flashing
The Start status indicator light flashes. The door was opened or the cycle was interrupted.
- Press the Start pad once and close the door within 4 seconds to start the dishwasher.
- To cancel the cycle instead, press and hold the Start pad for 3 seconds while the dishwasher is running.
Start LED flashing in a sequence
The Start LED flashes in a sequence. A critical fault is present.
Clean light
The Clean light is on. A wash cycle is complete. The light stays on as a reminder that the dishes are clean.
- Open the door, or press any key while the door is closed, to turn the Clean light off.
Source Source: Getting started: Cycle Indicator Lights and Sounds, p. 7
Sanitized light
The Sanitized light does not come on at the end of the cycle. The sanitizing conditions were not met.
The door was opened and the cycle was interrupted during the final rinse. Source: Troubleshooting Tips, p. 22
- Do not open the door during the wash cycle.
The incoming water temperature was too low. Source: Troubleshooting Tips, p. 22
- Raise the water heater temperature to between 120 °F and 150 °F.
Problems
- Dishes and flatware are not clean7 causes in the manual. First: the Ultra-Fine Filter assembly or the Fine Filter is clogged.
- Spots and filming on glasses and flatware6 causes in the manual. First: the water is extremely hard.
- Cloudiness on glassware2 causes in the manual. First: soft water combined with too much detergent causes etching, which is permanent.
- A white film on glassware, dishware and the interiorA low quality phosphate-free dishwasher detergent is the likely cause.
- Suds in the tub2 causes in the manual. First: the wrong detergent was used.
- Detergent left in the dispenser cupsDishes block the detergent cup, or keep its door from opening.
- Dishes do not dry4 causes in the manual. First: the inlet water temperature is low.
- Dishwasher will not run4 causes in the manual. First: A fuse is blown or the circuit breaker is tripped.
- Water is standing in the bottom of the tub2 causes in the manual. First: the air gap is clogged.
- Water will not pump out of the tubThe drain is clogged.
- Control panel lights go off while setting controlsToo much time passed between touching the selected pads. Each pad must be touched within 30 seconds of the others.
- The dishwasher beeps once every minuteThe door was left open during operation.
A white film on glassware, dishware and the interior
A low quality phosphate-free dishwasher detergent is the likely cause. Source: Troubleshooting Tips, p. 22
- Remove the film with a citric acid cycle. See Remove white film with citric acid.
Detergent left in the dispenser cups
Dishes block the detergent cup, or keep its door from opening. Source: Troubleshooting Tips, p. 20
- Reposition the dishes so water from the lower spray arm can flush the detergent cup and the cup door can open.
Water will not pump out of the tub
The drain is clogged. Source: Troubleshooting Tips, p. 21
- If you have an air gap, clean it. See Clean the air gap.
- If the dishwasher drains into a disposer, run the disposer clear.
- Check that the kitchen sink drains well. If it does not, you may need a plumber.
Control panel lights go off while setting controls
Too much time passed between touching the selected pads. Each pad must be touched within 30 seconds of the others. Source: Troubleshooting Tips, p. 21
- Touch any pad again to relight the panel, or open the door and unlock (top control).
The dishwasher beeps once every minute
The door was left open during operation. Source: Troubleshooting Tips, p. 19
- Press Start and close the door.
How-to
- How to clean the filtersEvery other month or more often with heavy use, and when wash performance drops or dishes feel gritty.
- How to clean the air gapWhenever the dishwasher is not draining well, if the sink has an air gap. The air gap is not part of the dishwasher and the warranty does not cover it.
- How to fill the rinse agent dispenserWhen the rinse agent is used up. The dispenser holds 3.5 oz (104 ml), about one month under normal conditions. The indicator window does not light up.
- How to remove white film with citric acidWhen a white film covers glassware, dishware or the interior.
- How to cancel a wash cycleTo stop a running cycle.
Maintenance
| Task | When | Source |
|---|---|---|
| Inspect and clean the Ultra-Fine Filter assembly and the Fine Filter | Every other month or more depending on usage | Source: Care and cleaning: Filters, p. 18 |
| Clean and de-odorize the interior with citric acid or a dishwasher cleaner detergent additive | Source: Care and cleaning: Dishwasher Interior, p. 17 | |
| Clean the control panel with a lightly dampened cloth, then dry thoroughly | Source: Care and cleaning: Control Panel, p. 17 | |
| Have a service technician protect the dishwasher against freezing if it sits in an unheated place over winter (professional service) | Source: Care and cleaning: Protect Against Freezing, p. 18 |
Settings
| Setting | Options | Notes | Source |
|---|---|---|---|
| Rinse aid setting | Rinse agent adjuster in the dispenser; clockwise for more, counterclockwise for less | Increase the setting if water drops or hard water spots remain after the dry cycle. | Source: Dispensers: Rinse Aid Setting, p. 8 |
| Control sounds | Press the Heated Dry/Dry Boost pad 7 times within 5 seconds, on models with that pad | Turns the control sounds on or off. The end-of-cycle double beep is switched the same way, and a triple beep confirms the change. | Source: Getting started: Cycle Indicator Lights and Sounds; Troubleshooting Tips, pp. 7, 19 |
Parts and consumables
| Item | Part number | Replace or refill | Specification | Source |
|---|---|---|---|---|
| Citric acid kit | WD35X151 | – | For dishwasher interior cleaning and white film removal; order through GE Appliances Parts | Source: Care and cleaning: Dishwasher Interior, p. 17 |
| Hard water test strip | WD01X10295 | – | Measures water hardness in grains per gallon to set the detergent amount | Source: Dispensers: Detergent Dispenser, p. 9 |
| Stainless Steel Magic | WX10X29 | – | For marks on stainless steel door panels (model numbers ending in SS) | Source: Care and cleaning: Exterior Door Panel, p. 17 |
| Rinse agent | – | – | High quality rinse agent such as Cascade Platinum Power Dry Rinse Aid or Finish Jet-Dry | Source: Dispensers: Use a Rinse Agent, p. 8 |
Specifications
Built-in dishwasher. GE's owner's manual 49-4000218 covers the GD*550–635, GD*450–535 and HD*310–330 series and marks features that vary as on some models. Source: Cover; Getting started, p. 1
The Start light is the status light. It flashes when the door was opened or the cycle was interrupted; flashing in a sequence is a critical fault that needs service. Source: Troubleshooting Tips, pp. 19, 21
Entering water must be at least 120 °F (49 °C) and no more than 150 °F (66 °C) for effective cleaning and to prevent dish damage. Source: Dispensers: Check the Water Temperature, p. 8
| Entering water temperature | 120–150 °F (49–66 °C) | Source: Dispensers: Check the Water Temperature, p. 8 |
|---|---|---|
| Normal water pressure | 20–120 psi | Source: Troubleshooting Tips, p. 19 |
| Rinse agent dispenser capacity | 3.5 oz (104 ml), about one month under normal conditions | Source: Dispensers: Filling the Rinse Agent Dispenser, p. 8 |
| Model number location | On the left-hand tub wall just inside the door; the last two letters show the door panel type (SS is stainless steel) | Source: Care and cleaning: Exterior Door Panel, p. 17 |
Recalls
No exact-model match for GDF535PSRSS in the U.S. Consumer Product Safety Commission recall database, checked . Recalls can name model families, so also check current recalls for GE Appliances.
Service contact
GE Appliances service: 833-426-3393, products.geappliances.com/appliance/gea-specs/GDF535PSRSS/support. United States (Canada: 800.561.3344). Source: Consumer Support, p. 24
Sources
- Owner's Manual, Dishwashers GD*550-635, GD*450-535 and HD*310-330 series. GE Appliances, a Haier company. Document 49-4000218, revision Rev 5, 72 pages, en-US. images.salsify.com (PDF). Listed on the manufacturer's support page. Retrieved 13 November 2026.
Page numbers are the numbers printed in the manual. Where this page and the manual differ, follow the manual.
All GE Appliances handbooks. Report an error to hello@modelhandbook.com.