Lg washer error code ie

The washer is not getting enough water.

Cause 1 of 6The water faucets are not fully open. Source: Troubleshooting: Error Messages, p. 37

First checkOpen both faucets all the way.

Causes and checks

The water faucets are not fully open. Source: Troubleshooting: Error Messages, p. 37
1. Open both faucets all the way.
A water inlet hose is kinked, pinched or crushed. Source: Troubleshooting: Error Messages, p. 37
1. Straighten the hoses. Make sure none is pinched against the wall or under the washer, and take care when moving the washer during cleaning or maintenance.
The water inlet filters are clogged. Source: Troubleshooting: Error Messages, p. 37
1. Clean the water inlet filters. See Clean the water inlet filters.
Water pressure at the faucet or in the house is too low. Source: Troubleshooting: Error Messages, p. 37
1. Run another faucet in the house to check pressure and flow.
2. Disconnect the inlet hoses from the washer and run a few gallons of water through them to flush out dirt.
Licensed plumber If the flow is too low, have a plumber repair the supply lines.
The supply is connected with leak-limiting hoses. Source: Troubleshooting: Error Messages, p. 37
1. Replace the leak-limiting hoses with standard hoses. LG says they can trip falsely and stop the washer from filling.
The end of the drain hose is lower than 29.5 inches (75 cm) above the bottom of the washer. Source: Troubleshooting: Error Messages, p. 37
1. Raise the end of the drain hose to more than 29.5 inches (75 cm) above the bottom of the washer.

If the checks above do not clear it, contact LG Customer Information Center: 1-800-243-0000, lg.com/us/support. United States (Canada: 1-888-542-2623). Source: Limited Warranty: To Obtain Warranty Service, pp. 45, 49

UE: The load is out of balance, so the washer cannot spin it.
OE: The washer cannot drain.
dE: The lid is not closed properly.
dL: The lid is not locked properly. The washer does not run unless the lid is locked.
LE1: A foreign object, such as a coin, pin or clip, is caught between the pulsator and the inner tub. On some models LE shows first and then 1.
LE: Motor locked error.
tE: Control error (temperature sensor error).
FE: The water level is too high because of a faulty water valve (overflow error).
PE: The water level sensor is not working correctly (pressure sensor error).
Eb: Clutch error. The manual calls it a mechanical failure.
Ps: The supply voltage is not correct.
CL: Not a fault. Control Lock is on.
dr: Not a fault. The special drain feature is running. A cycle that stays paused for more than 4 minutes is canceled and the water left in the tub is drained.
tCL: Not a fault. Tub Clean is running or due. On some models tc shows first and then L.
ub: Not a fault. The washer has detected an out-of-balance load and is trying to rebalance it.

Owner's Manual, Washing Machine WT7150C* / WT7000C* / WT7010C*. LG Electronics Inc. Document MFL68267084, revision Rev.04, 2026-10-02, 52 pages, en-US. gscs-b2c.lge.com. Listed on the manufacturer's support page. Retrieved 12 November 2026.
Owner's Manual, Washing Machine WT7880H*A / WT7900H*A. LG Electronics Inc. Document MFL68267072, revision Rev.05, 2025-10-10, 60 pages, en-US. gscs-b2c.lge.com. Listed on the manufacturer's support page. Retrieved 12 November 2026.

Page numbers are the numbers printed in the manual. Where this page and the manual differ, follow the manual.

Applies to: WT7150CW, WT7900HBA. United States and Canada.
Source: Owner's Manual, Washing Machine WT7150C* / WT7000C* / WT7010C*, MFL68267084 revision Rev.04, 2026-10-02; Owner's Manual, Washing Machine WT7880H*A / WT7900H*A, MFL68267072 revision Rev.05, 2025-10-10
Last verified: 12 November 2026
Handbook: LG WT7150CW and WT7900HBA top-load washers in Washers; all LG handbooks